cheapest PC repair.com

Posts Tagged ‘power cable’

Are you getting the 3 red light error or red ring of death? If so, don’t immediately assume that your console is defective. You may be having difficulties with getting power to your console.

This problem is very easy to deal with and you want to rule this out before sending your Xbox off for repair. Too much heat is the normal explanation for getting 3 red lights. But unless it is very obvious that you have a heat problem, you should first make sure that the machine is getting adequate power.

First, you should begin with the 110 AC power outlet in your wall. You may have had a momentary power brownout to your house. This is guaranteed to cause problems with your console.

If such is the case, the console should work after restarting it. If not, look at the power supply light on the box at the halfway point of the power cord.

If there’s a green light, you have plenty of power so the problem lies elsewhere. If this is the case, you can stop reading this article since I will deal with power supply problems here.

If you see a red or orange light or no light at all, then your console isn’t getting enough power. There are a number of causes for this:

1.) The wall outlet in your room is at fault.

Connect the power supply of the console into another outlet in another room.

2.) You have a bad power strip or defective surge protector.

Bypass any surge protectors or power strips by plugging the power cord directly into the wall outlet.

3.) The power supply cables to the console aren’t properly connected.

Disconnect and reconnect all power cable connections starting from the console and proceeding all the way to the wall outlet.

4.) The power supply cables are damaged.

Replace any damaged cables.

5.) Your power brick is overheating.

The power brick is not getting adequate ventilation. Place it on a hard surface away from anything soft like a shag carpet.

6.) Your power brick is damaged.

Borrow a power brick from your friend or use a spare that you already own. If that solves the problem, then the problem was a defective power brick.

This article presented a trouble shooting procedure for the 3 red light error that’s related to inadequate power supply. I sincerely hope that this solves your troubles because the other causes are much more difficult to resolve.

Try these comprehensive 3 red light error tips before spending time or money on Xbox repair. This Xbox 360 trouble shooting information is free.

Article Source: Xbox – Feeling Lucky? The 3 Red Lights May Be This Easy To Fix

Many devices are using usb charger at present like GPS, iPhone, iPod, MP3 etc. One will find one lighter socket splits along with one lighter socket in an usb charger. These sockets are placed in such a way that one will not find problems in plugging and unplugging. The usb charger has sleek surface. It results large power output.

Also the main usb charger adapter plays an important role in supplying power to lots of devices from a particular charger. The usb charger gets very easily plugged in one’s usb power cable. It also uses LED power indicator. The usb charger are quite smaller , having less weight and having a compact body. It also gives an output of about 5V as one finds in computer and laptop usb port.

The usb charger is a unique product in the market for those consumers who have usages of many devices getting charged with one’s usb cables. The usb charger works to connect these devices to the usb main charger so that they get plug in the main power supply for charging. The usage of LED in the usb charger helps in determining when the main charger adapter is giving power. Its prescence is seen in certain electronic products such as mobile phones, PDAs,bluetooth headsets and many other devices which have usb charger backing.

To read about cles usb and other information, visit the oreillette bluetooth site.

Article Source: usb charger

Do you know what is inside your computer? Maybe you peeked when the service technician was installing something for you. When you first open up the CPU and look inside, a computer is a very threatening machine. But once you know about the different parts that make up a complete computer it gets a lot easier. Today’s computers consist of around eight main components; some of the advanced computers might have a few more components. What are these eight main components and what are they used for? We will start with beginner level details to get you started.

First is the Power Supply. The power supply is used to provide electricity to all of the components in your computer. It is usually a rectangular box and is usually positioned in one of the corners of the computer. To find it for sure, look to see where the power cable plugs into the back of the computer and you have found the power supply. Most power supplies today are calculated in wattage and come in 50 watt increments (500 watt, 550, 600, etc

Second is the Motherboard. All of the components are connected into the motherboard; it doesn’t mean that it is the brain of the computer. Yes it holds the brain and helps it act together with all the other components of the machine.

The third and a very important component of a computer is the CPU (Central Processing Unit), Known as the brain of the computer and nothing is going to happen without it. All major calculation performed by a computer are carried out inside its CPU. It is also responsible for activating and controlling the operations of other units of the system. The faster the CPU can do these calculations and give the correct answers, the faster the computer runs for the user. CPUs are now measured in gigahertz (Ghz) and they are at present up to our 3.8GHz or faster

A fourth component is the RAM (Random Access Memory). RAM is used as momentary working storage for the computer. We have different types of RAM memory with different speed, but it should match with your motherboard so that it can work properly. The more RAM you have in your computer, the better your computer will work.

The fifth component is the Hard drive. This is where you can store everything. Our material on the hard drive includes the operating system (Windows XP, etc), games, and different types of software, etc. over the year the capacity of the hard drive is continuously improving and in the interval of few years its capacity have gone from around 20MB to over 500GB and more. So you can store a lot more information on your computer such as games, pictures, videos, applications, and more.

Sixth component is Cooling fans. Often most computers come with one cooling fan or it might have several. Its help to cool down the heat generated by others components, Such as power supply, the CPU, and some high-end video cards. The work of all of your cooling fans is to get this heat out of the case so that nothing overheats and breaks. While most of the noise you hear coming from a computer can be credited to the cooling fans, remember to be tolerant. The cooling fan is your friend!

Our Seventh and final component is the mixture of several different devices. These are the Cd-rom, DVD drives, floppy Drive and Backup devices such as external hard drive.

Article Source :- http://www.technologyb2b.com
For more technology related Article visit :- http://www.technologyb2b.com

Article Source: components of computer

A hard disk is comprised of several disk-shaped platters that rotate rapidly mounted on a shaft. These platters are magnetically coated with a similar material that is used magnetic recording tape. If not exposed to external conditions like temperature, water, vibrations etc, hard disk can remain functional for a long time. However, if it already suffers manufacturing faults, hard disk may crash unexpectedly. Hard disk contains a set of moving parts and that’s why, it has high odds to get wear out. In all such cases, Hard Drive Data Recovery experts come to rescue. They can extract lost information from such physically damaged hard drives using advanced tools and procedures.

Consider a situation, you power on the system and hard disk fails to spin up. Possible reasons could be:

Spindle motor is crashed: Hard disk spindle motor provides power to platters so that they may spin up. They allow them to rotate. It can get crashed if hard disk suffers high intensity shocks. A hard disk with crashed spindle motor can’t spin up. It can also happen if shaft is damaged or twisted

Head crash: Read/write head is the moving component that is responsible for accessing data from hard drive recovery software . It floats at micrometer distance from platters’ surface. If one or more heads get crashed over this surface, they may prevent platters to spin up.

Logic board is damaged: Logic board is the circuitry that controls all hard disk internals. Due to short circuits and unexpected power failure, it may get damaged. In such cases, hard disk doesn’t get power and fails to spin up.

If you observe that hard drive is not spinning up, verify that power cable is properly attached and is in good condition first. If you find it correct, then probably your hard disk is physically damaged. You need to turn off the system immediately and use anti-static and shock-proof material to pack it and send to a hard drive recovery service center. In this recovery service, experts deal with physically failed hard drive to extract lost data. Hard Drive Data Recovery experts follow some standard and advanced recovery techniques, like replacing or repairing damaged internals, displacing misaligned platters etc.

Stellar Information Systems Limited offers industry’s leading Hard Drive Recovery service for all sorts of physically damaged hard drives. It is offered through Class 100 Clean Rooms. Stellar provides complete and confidential disk recovery service for all makes of hard drives, including SCSI, SATA, IDE and EIDE.

Shally Spears a student of Mass Communication doing research on hard drive recovery software . He is also a freelancer for partition recovery software .

Article Source: Hard Disk Doesn’t Spin Up

When a computer system is powered up, BIOS (Basic Input/Output System) is the first program (a firmware that is software on hardware) executed by a computer system. The BIOS detects, tests and initializes system devices like hard drives, optical drives, keyboard, display screen etc. After the BIOS check is over, computer system files take control to detect the hardware and software environment. Among all computer storage media, hard disk is the most common one due to its large storage capacity and cost-effectiveness. When the hard drive fails due to hardware issues, BIOS fails to detect it. This generally happens when hard disk suffers physical issues related to one or more of its internals. Attempting to run such failed hard drives can cause more damage to your data. So, if you ever encounter such issues, it is recommended to power down the system immediately and consult data recovery solution providers for recovering lost data.

The first function of BIOS is to run POST (Power-On Self Test) that is stored on a predetermined address in memory. This code is responsible to gather information of all attached drives including hard disk. It makes sure that all hardware is working properly and the minimum hardware required is available. Thus, if the hard drive is damaged, POST may not detect it.

In particular, BIOS may fail to recognize the hard drive post issues as physical crash. But, there can be other issues as well like:

• You have recently changed the BIOS settings and hard disk is not correctly configured.
• Hard disk is inappropriately connected to the system. Power cable or interface cable is damaged or not attached to the mainboard.
• Jumper settings are not correct.
• Hard drive controllers are disabled in BIOS.

To solve the issue, you need to follow these steps:

• Set your BIOS settings to default
• Verify all cables are in good condition and are properly connected
• Check jumper settings. If you have attached two hard drives to a port/connector, make sure that one of them is configured as master and other as slave
• Make sure that all/in-use hard disk controllers are enabled
• If the problem continues, you require a hard drive recovery company that has all the modern facilities and tools to recover lost data.

Data Recovery service incorporates cutting-edge technologies and tools that are intended to recover lost data. When you first send your failed hard drive to a recovery company, the recovery experts scrutinize it under safe and controlled lab environment of Clean Rooms. Based on such analysis, suitable recovery procedures are followed to recover optimum lost data. For example, if your hard disk is damaged due to read/write head crash, experts repair or replace it.

Stellar Information is industry’s leading provider of quality data recovery services. Stellar’s recovery experts work under state-of-the-art Class-100 Clean Rooms. The recovery solutions are available for almost all makes and models of hard drives (SCSI, SATA, EIDE and IDE), USB flash drives and SSDs (Solid State Drives: SATA). Stellar provides complete data recovery solutions for Server, RAID, SAN and NAS hard drives.

K madhav is a data recovery expert and doing research on data recovery software and hard drive recovery.

Article Source: What You Do When BIOS Fails to Detect Hard Drive

Battech’s 3 in 1 Data Cable is a unique gadget which combines a mini power pack, USB charger and data cable in one slim line device, making it perfect for consumers on the go.

Andrew Lim, Mobile Phones Editor for CNET UK, reviewed this gadget and had this to say about the item:
“In an attempt to make sure you’ve always got enough juice, iPhone lovers, it’s definitely worth investing in a portable charger. But Battech has come up with something even better.
Combining a USB data cable that works as a USB charger and comes with a built-in battery pack, this compact device is very handy indeed. When you want to transfer music or charge your iPhone up using your PC, you simply plug it into your computer, but you can also plug it in when you’re out and about too.
Battech have come up with something handy that could be a lifesaver.”
You can read the full review on their website.

Battech’s rechargeable power cable is perfect for powering and charging your iPhone and iPods as well as transferring data, and it’s so simple to use.
Battech iPower 3 in 1 Charger specification
l Lithium polymer battery
l Safe and high reliability
l Compatible with: iPhone, iPod
l Rechargeable (500+ cycle times)
l Long runtime for your gadgets: 30hrs for iPod and 1.5hrs talk time for iPhone

The 3 in 1 Data Cable can be purchased at HMV stores and via Battech’s website.
About Battech International Limited
This iPower 3 in 1 Charger further strengthens Battech’s portfolio of advanced rechargeable portable power solutions, incorporating some of the most advanced battery technology on the market today.

Battech is also a leading manufacturer of high performance primary and rechargeable batteries offering cells to B2B and B2C market sectors. We sell various types of batteries and chargers including: Lithium Ion, Polymer Nickel-Metal Hydride (NiMH).

Headquartered in the UK, our advanced cell technology division is based in Hong Kong and the manufacturing facility is based in Shenzen, China.

For more information on this gadget or Battech contact us via:

Website: http://www.battech.co.uk

Telephone: 0871 550 0051

Address: Battech International Limited
Unit 1 Marlowe Court
Whitchurch Business Park
Whitchurch
Shropshire
SY13 1QR

Article Source: CNET UK raves about Battech’s 3 in 1 Data Cable

During POST or Power On Self Test, computer BIOS attempts to get information regarding all of the devices attached to your computer system. After examining the processor and primary memory (RAM), it checks for the devices like hard drive, CD ROM etc and shows them with messages on screen like ‘Found Primary Master’ and ‘detecting IDE drives’ etc.

-> POST (Power On Self Test) is the first thing done by BIOS when your computer first boots up. POST is an in-built diagnostic program, which examines the hardware of your computer system to make sure that everything is available and working properly.

Many times, the BIOS of your computer just declines to recognize the hard drive, basically makes it unusable- there is no way in which your operating system will recognize the hard drive if BIOS can not. Let’s observe why all this happens.

The most frequent reason of this problem is a badly connected or loose data cable. You should first ensure that data cable is properly plugged in, both into the motherboard as well as the hard drive.
The same thing goes for the power cable, so you should check it as well. You should also make sure that red lines on data cable and the power cable are contiguous to one another.

Once you have ruled out the cable problems, you need to check out the jumper settings on hard drives. If two hard drives are attached to a port, ensure that one is set as masters and other as slave.
Next, ensure that the hard drive controllers on motherboard are not disabled. These hard drive controllers control the IDE devices and without them BIOS could not detect the hard drives.

If any of the above mentioned methods does not work, you need to search for a data recovery expert to cure your hard drive. It seems that hard drive has some internal problems, which can not be cured without opening it. And you are not recommended to open your hard drive at your own.

Data recovery experts are highly qualified and trained professionals, who know all ins and outs of the hard drive and are able to fix most of the physical hard drive problems. To ensure absolute and safe data recovery, always go for the experienced and reliable data recovery company.

Stellar Information Systems Limited is the most trustworthy and leading data Recovery Company, having more than 15 years of rich experience. Stellar’s personalized data recovery services is offered by highly trained data recovery specialists through Class 100 Clean Rooms.

Williamz Jack work as a freelancer and researcher of Data Recovery & File Recovery Software.

Article Source: What to Do When BIOS Does Not Recognize the Hard Drive?

Microsoft’s latest Xbox 360 features a new motherboard and a new graphics chip that ought to put out less heat than the older chip design. Whether this new generation of Xboxes has eliminated the ring of death fault is still an open question. Only time and plenty of use by the world’s consumers under lots of different conditions will decide the verdict.

For those of us who still have the older Xboxes, the ring of death and other heat related problems are still a fact of life.

This article will discuss a few troubleshooting tips that you can try before sending your Xbox off for repair.

1.) This first suggestion is pretty lame but this article isn’t complete without it: Restart the console.

2.) If this doesn’t do anything, then perhaps the trouble may be a cable or cord that’s come loose. First, disconnect all power cords and cables that are detachable from the Xbox. Then unplug the power cable from the wall outlet.

Now the cords and cables should be reconnected to your Xbox. Plug the power cord back into the wall and turn on your Xbox.

3.) If this doesn’t help, turn off the console, unplug the power cord, and detach the hard drive. Plug the power cord back in and power up the console. If you don’t see any red lights, turn off the console and disconnect the power cable. Finally, put in the hard drive, plug the power cord back into the wall, and switch the console on.

4.) The power cord contacts have been known to heat up and melt. This has happened to Xboxes that were played over very long periods of time (about 12 continuous hours). This usually happened when the Xbox had an intercooler.

The contacts should be checked for heat damage. Sometimes the Xbox operates just fine when you pull up on the power cable. But the red ring of death error lights turn on when you pull down on the power cord. Get another power cord if this is your problem.

5.) If your console has been heating up, then give your Xbox an occasional rest so that it can cool off. Keep the cooling vents clear of obstructions and use your Xbox in open and well ventilated areas. Be careful that there are no sources of heat next to the Xbox.

Vacuum any dust buildup that you find inside the console. Place a small fan near your console to keep it cool. Remember that the power brick has to stay cool, so keep it off of soft material such as shag carpeting.

It too should be in an uncluttered area that has ventilation. You may want to try hanging the power brick from its cord using a hook.

So these are your troubleshooting options for the red ring of death that won’t demand any repair work. If your problems were still not solved, the next step is to use your warranty or have your console repaired. Remember, the warranty is void if the console is opened for any reason.

Marc Sandford is a gaming enthusiast and writer. Get more Xbox troubleshooting information about fixing the Red Ring of Death.

Article Source: Xbox 360 3 Red Light Error – 5 Easy Tips